2023 Haybuster® Tub Grinders 1155

2023 Haybuster® Tub Grinders 1155

Swipe to View More

  • Year 2023
  • Make Haybuster®
  • Model Tub Grinders
  • Engine C15
2023 Haybuster® Tub Grinders 1155

2023 Haybuster® Tub Grinders 1155

2023 Haybuster® Tub Grinders 1155

Features may include:

ROTARY SELF-CLEANING SCREEN

The enclosed engine compartment, and Rotary Self-Cleaning Screen protects the engine from dirt and debris buildup. An enclosed engine also reduces the noise level. The 1155 also gives you easy access to the engine with a 3-door entry on either side, plus a front door for access to the radiator.

C15 CATERPILLAR ELECTRONIC DIESEL ENGINE

Powered by either a 475 HP (354 kw) or a 540 HP (403 kw) C15 Caterpillar Electronic diesel engine whose state-of-the-art electronic fuel injection system decreases fuel consumption and allows it produce ground hay at a rate that will make you money on every job. It’s strong enough to chew through those tough, wet, bales, and has all the features you’ve come to expect from Caterpillar; like reliability, cold weather starting, unsurpassed product support, and proven resale value.

KPTO FLUID COUPLER

The KPTO Fluid coupler transmits power with up to 98% efficiency and eliminates the mechanical clutch. It’s goof proof, can engage or disengage at full engine rpm without damage and requires minimal maintenance.

50° OSCILLATING STACKING CONVEYOR

The 30-inch Wide x 26-ft. Long stacking conveyor piles hay to over 18 feet in height. The conveyor can oscillating left to right up to 50 degrees, which means you can not only make the pile tall, you can also make it wide.

50" BIG BITE HAMMERMILL

The Big Bite hammermill is located at the rear of the sub frame, reducing the length of the belly conveyor, improving the belly conveyor service accessibility, and moving the dust away from the operator. The hammermill is also dynamically balanced to give you smoother operation, longer life, and less maintenance.

90 DEGREE TUB TILT

The 11 ft. wide x 50 in. deep tilt tub opens a full 90 degrees for access to the hammermill and screens as well as for normal servicing.

300 GALLON FUEL TANK

11' TUB WITH TIP IN TUB FLARES (SIDES)

The 11 ft. wide x 50 in. deep tub has tip in tub flares (sides) . The sides are folded in to narrow the transport width of the grinder.

ENCLOSED ENGINE COMPARTMENT W/ EASY ENGINE ACCESS

The enclosed engine compartment and Rotary Self-Cleaning Screen protects the engine from dirt and debris buildup. An enclosed engine compartment also reduces the noise level. The 1150 also gives you easy access to the engine with a 3-door entry on either side, plus a front door to the radiator.

Engine

Engine Manufacturer CATERPILLAR
Engine C15
Engine Type In-line
Cylinder Liners 6
Stroke 4 | 6.5 in (165 mm)
Engine Power 475 HP (354 kw) or 540 HP (403 kw)
Bore 5.4 in (137 mm)
Displacement 983 cu. in. (14.6 L)
Aspiration Turbocharged and air to air aftercooling
Compression Ratio 16.25 : 1
Cooling Oil to air, thermostatic controlled electric fan | Oil to Air, radiator mounted

Fuel System

Fuel Type Diesel
Fuel System Electronic Unit Injector

Drivetrain

Drive System Hydraulic, Top driven | Direct from Fluid Coupling | Mechanism: Electro/Hydraulic | Hydraulic | Idler Rollers Type: “Easy Clean”

Electric

Electrical Engine Block Heater: 120V / 2000 watt

Operational

Operating Conditions Screen Area: 2,781 sq. in. (7,063.75 sq. cm.)

Hydraulics

Hydraulic Pump Gear type, 2 section, output is 25 & 15 gpm @ 2100 psi., engine mounted

Lights and Safety

Lighting Clearance, Directional, and Brake

Dimensions

Transport Width 11 ft. (3.35 m)
Transport Height 11 ft 6 in (3.51 m)
Transport Length 31 ft (9.448 m)
Dimensions Type: Rubber Belt with 1-1/2 in (38.1 mm) Cleats | Type: Rubber Belt with 3/4 in (19.05 mm) cleats | Tub Floor Thickness: 1/4 in (6.35 mm) | Tub Wall Thickness: 12 gage (2.66 mm) | Tub Diameter at Base: 9 ft (2.74 m) | Screens: 1/8 in (3.18 mm), 3/16 in (4.76 mm), or 1/4 in (6.35 mm) thick and various hole sizes from 1/8 in (3.18 mm) to 8 in (203.2 mm) | Bearings: 4 in (101.6 mm), Pillow Block Bearings | Mill Shaft: 4-1/2 in (114.3 mm), Stress Proof Steel | Mill Plates: 1/2" (1.27 cm) thick X 16" (40.64 cm) dia. | Hammer Rods: 1-1/4 in (31.75 mm) dia., Case Hardened | Hammers: 1/2” (1.27 cm) AR-Hardened Steel , Swing | Feed Opening: 25 in x 52 in (63.5 cm x 133 cm) | Diameter, Hammers Extended: 26" (66.04 cm) | Conveyor Articulation: 2) 2 in x 8 in (5.08 x 20.3 cm) | Conveyor Fold: 2) 3 in x 30 in (7.62 x 76.2 cm) Hydraulic Cylinder | tub Tilt: 3 in x 30 in (7.62 x 76.2 cm) Hydraulic Cylinder | Conveyor Lift: 2) 3 in x 36 in ( 7.62 x 91.44 cm) Hydraulic Cylinders
Length 50" (127 cm) | 26 ft. (7.92 m)
Height Loading: 9 ft 6 in (2.89 m) | Max. Conveyor Discharge: 18 ft 3 in (5.56 m)
Width Tub: 11 ft (3.35 m) | 36 in (91.4 cm) | 30 in. (76.2 cm)
Depth, Maximum 50 in. (127 cm)

Capacities

Cooling System 9.2 gal. (34.8 L)
Oil capacity Lube Oil System (refill): 10 gal (38 L)
Features Axle: Tandem, rated 22,500 lbs. | Fluid Capacity: 9.24 gal (35 L) | Reservoir Capacity: 50 gallon (171 liter) | Fire Suppression: 2) 20 lbs (9.09 kg)
Fuel Capacity 300 gal (1,135 L)

Weights

Weight Total: 34,100 lbs. (15,468 kg) | Axle: 27,900 lbs. (12,656 kg) | Tongue: 6,200 lbs. (2,813 kg)

Features

Features Oscillation (50°): Electric/Hydraulic | Fold: Electric/Hydraulic | Lift: Electric/Hydraulic | Speed control: Electronic Governor | Mill Feeding: Mill Grate | Towing Arrangement: 5TH WHEEL | Control Valves: Electric/Hydraulic, 4 valves - 1) 4 spool, 2) single spool, and 1 proportioning | Maintenance: Easy access oil filter and drain plug | Charge Pump: Gear type | Drain Type Fluid Coupling | TRANSFLUID | Rotation (from flywheel end): Counter-clockwise | Radiator: Staggered Core with 7 fins per inch
Hammer Quantity 88

Product Photography